Product Categories

Heal and Seal D2K (5 GAL Kit) SLR-DECO2K

deco-d2k-concrete-sealer-walttools-5-gallon
deco-d2k-concrete-sealer-walttools-5-gallonheal_and_seal_decoheal_and_seal_deco_on_pres_slatehns_sealed_and_unsealed_2wet_look_paver_sealer2fullsizerender
5 5 3 Product
$299.00 each Weight: 43 lb


Heal and Seal D2K takes the durability and resiliency of the original Heal and Seal Deco and makes it into an uncompromising, "apply-and-forget-it" product. To put it simply,  D2K is the very best decorative concrete sealer on the market for its coverage, durability, and ease of use. D2K will provide color enhancement and a satin to glossy finish. 

KEY POINTS:

  • Two-part system
  • Better coverage than acrylics
  • Increased durability
  • Superior chemical-resistance
  • High heat-resistance
  • Phenomenal UV-resistance
  • Excellent against road salt and related chemicals
  • Coverage is approximately 275-300 sq ft/gallon with single coat coverage in many cases.
  • Apply with inexpensive garden sprayer and roller
  • Water cleanup

D2K can be used to replace your current sealer and provide stellar results. D2K contains NO acrylic resins. Instead, it works through an advanced silicon technology that provides a permanent treatment to protect and preserve your concrete longer than any acrylic-based sealer could possibly do. This concrete sealer will penetrate and chemically fuse just below and above the surface of the concrete, as shown in Figure 1 below. This prevents water and other materials from getting below the surface and causing issues. This fused layer will also fill and heal small imperfections in the surface that would eventually lead to both aesthetic and physical imperfections in the surface. These imperfections can lead to color fade, concrete dusting, pop-outs, scaling, and even cracks (Figure 2). Standard sealers do not offer the level of protection that D2K can provide. If applied properly, it will never peel like a traditional sealer because it is more than just a plastic skin sitting on the surface. Once chemically bonded into the surface it will not peel and flake away. It is a permanent treatment that will only wear away as the actual concrete wears. This sealer protection will continue to keep your concrete healthy down below even when the top layer eventually shows wear.

Do yourself a favor and protect your investment with the only decorative concrete sealer that will maintain the health and welfare of your beautiful hardscape.

In addition to decorative concrete surfaces, D2K is also an excellent choice for restoring the color of weathered pavers. It is very easy to apply and provides instant gratification with minimal cleanup.

HOW TO USE:

MIXING: Always mix product before using to ensure correction of any possible separation that may have occurred. Material may separate during long term storage. Highly-recommended to use a drill mixer with a mix head that lifts material toward the top surface to ensure a good blend. Blend for 2 minutes.

APPLICATION: Concrete should be clean and dry. Any previous sealer or coatings should be stripped and removed to ensure D2K is able to reach the concrete surface. It is always recommended to wait at least 28 days before applying to newly poured slabs. Excess moisture in the concrete can slow the curing process of the sealer and delay the time at which you are fully protected.

Standard Application Method: Spray with a quality sprayer that has a conical type tip and then back roll the sealer. Apply with slight overlap on spray passes taking care not to create heavy puddles. Another person should begin rolling the material out into an even coating, making sure they redistribute heavier areas of the sealer onto lighter areas. You should quickly find that the sealer spreads out quickly and easily into a nice even coating. Failure to apply with this method can result in uneven darkening of the surface. When sealing countertops you need to be sure you are always rolling out material with a wet roller. Always be pushing material in front of the roller and working it into the surface. When the surface is fully coated you can then continue to roll out until material is gone. You may even "wring out" your roller of excess material if too much is on the surface once it is fully coated.

D2K will create a white surface that will absorb and react with the concrete surface, and cures clear as this happens. Failure to remove puddle areas can result in areas that will cure out much slower. Allow to dry for a minimum of 1 to 2 hours depending on current conditions of temperature, humidity, and starting moisture in the concrete. For best results, allow D2K to cure for up to 12 hours, if possible. Once cured you can resume normal activity on the surface. In most cases, a second coating is not necessary unless there is a visual indication that some areas absorbed much more material than others. If so, the second coating should be applied only after the initial coating has cured and is NO LONGER TACKY. Follow the same application procedure.

WARNING: Areas that remain white are indications of moisture present in that area or the material being applied to thick in that area. These areas could take a few extra days to cure fully but always do.

PLEASE NOTE: It is always recommended to test the product in a small, inconspicuous area (on the same concrete substrate) for desired results prior to application. Coverage rates may vary for all coatings and substrates depending on porosity, density, texture etc. When applying, do not exceed 400 sq. ft. per gallon. Applying too thin of a coating may cause inadequate film formation or performance expectations may be limited.

     

Figure 1                               Figure 2

 

 

 

 

prop 65 - ethylbenzene - sm.jpg

Product Reviews:
5 1 5
No vote yet
I’ve tried to make it fail, tried to make it peel, yellow tape, blue tape, cuck tape on for two weeks, no peeling no failure – this stuff is awesome
5 1 5
No vote yet
The only water based sealer I trust to make the detailed colorations I create POP. While providing long lasting protection without the fear of application!
5 1 5
No vote yet
I used this a couple years back. I like it but it took a while to cure fully. Almost 3 days some times. Never had to reseal one yet though which is nice. I talked to Don over at the store and he said they made some changes to improve the cure rate. They sure did. Seal one day, furniture back on the next. Perfect. I think it is a little less shiny now but that is what I am being asked for anyway. Its a great semi gloss. This stuff is a home run in my book.
You must have bought this item in order to post a vote or a comment

Sign Up For Contractor Source Info and Specials

Contact Us

Contractor Source, LLC
1246 Leah Rd
Morris, IL 60450
Tel : 1-888-263-5895

Follow Us

Back To Top